Bicycle wheel bearings are located inside the wheel hub. Though they are easily accessed on front wheels, you may need to remove the sprockets to access a rear wheel hub. If you've ever changed the bearings on a cup-and-cone style bottom bracket, you will recognize the similarities in many steps of this process.

  Advertisement
 
Step 1
     Take the wheel off the bike. Release the brakes and unclamp the quick release or use the 17 mm wrench to unscrew the clamping nuts.

  Advertisement
 
  Video of the Day
  
Step 2
     Remove the freewheel or cassette, if required. It is generally possible to change wheel bearings in the rear hub without removing the freewheel, but it may be more difficult. If you have a cassette, you will have to remove it.

  Advertisement
 
Step 3
     Unscrew the locknut and remove the washers, spacers and dustcaps, if present, from one side of the axle, which is the thick threaded tube running through the wheel's hub, with the 15 or 17 mm wrench. If you are working on a rear wheel, remove the locknut on the side of the hub opposite the freewheel or cassette.

  Advertisement
 
Step 4
     Use the correct size cone wrench to unscrew the cone from the axle. Pull the axle out of the opposite side of the wheel. Hold the wheel upright when you remove the axle. Several ball bearings may fall out.

  Advertisement
 
Step 5
     Remove the ball bearings from both sides of the hub, place them on a rag and count how many came from each side. Wipe them with a rag and examine closely for pits or scratches. Discard any damaged ball bearings. Generally, front wheels use ten 3/16-inch bearings on either side of the hub and rear wheels use nine 1/4-inch bearings on either side.

  Advertisement
 
  Advertisement
 
Step 6
     Wipe the cups that held the ball bearings clean. Thoroughly coat the inside of the cups with new grease. Use enough that a ball bearing sticks firmly in place when placed in the cup.

  Advertisement
 
Step 7
     Lay the wheel flat with the side of the hub from which you pulled the axle facing up. Place the correct number of bearings in the cup. Gently flip the wheel over. If bearings fall out, add more grease to hold them in place.

  Advertisement
 
Step 8
     Insert the ball bearings in the other cup. Slide the axle back into the hub in the same orientation in which it was pulled out.

Step 9
     Screw the cone back onto the axle. When it contacts the bearings, stop. Rotate the axle and push it back and forth. If it moves, screw the cone in more. When the hub makes a slight grinding sound when the axle rotates, unscrew the cone a quarter-turn at a time until the noise stops and then unscrew it one quarter-turn more. This allows for the inevitable slight tightening of the cone when you reattach the spacers, washer and locknut without causing grinding.

Step 10
     Reattach the spacers, washer and locknut and place the wheel back on your bike.

Things You'll Need

17 mm wrench Freewheel or cassette removal tools 15 mm wrench 13 mm cone wrench 15 mm cone wrench Rags 20 ball bearings, 3/16 inch 18 ball bearings, 1/4 inch Bicycle or automotive wheel bearing grease Tip Fifteen and 17 mm wrenches and 13 and 15 mm cone wrenches are the correct sizes for many bikes. Your bike may require wrenches of a slightly smaller or larger size.

  Advertisement
 
  Advertisement
  
  references & resources
  
      Sheldon Brown: Overhauling &ampamp; Repacking Hubs
    
      BikeWebSite: Bicycle Tune-Up Step 3 -- Adjust The Front Wheel Bike Hub
    
      Bicycle Tutor: How to Overhaul Wheel Bearings
    
      Sheldon Brown: Shimano Cassettes &ampamp; Freehubs
    
      Sheldon Brown:Traditional Thread-On Freewheels
    
      Sheldon Brown: Freewheel or Cassette?
       




  references & resources
  
      Sheldon Brown: Overhauling &ampamp; Repacking Hubs
    
      BikeWebSite: Bicycle Tune-Up Step 3 -- Adjust The Front Wheel Bike Hub
    
      Bicycle Tutor: How to Overhaul Wheel Bearings
    
      Sheldon Brown: Shimano Cassettes &ampamp; Freehubs
    
      Sheldon Brown:Traditional Thread-On Freewheels
    
      Sheldon Brown: Freewheel or Cassette?
  • 17 mm wrench
  • Freewheel or cassette removal tools
  • 15 mm wrench
  • 13 mm cone wrench
  • 15 mm cone wrench
  • Rags
  • 20 ball bearings, 3/16 inch
  • 18 ball bearings, 1/4 inch
  • Bicycle or automotive wheel bearing grease

Fifteen and 17 mm wrenches and 13 and 15 mm cone wrenches are the correct sizes for many bikes. Your bike may require wrenches of a slightly smaller or larger size.

      Sheldon Brown: Overhauling &ampamp; Repacking Hubs
    
      BikeWebSite: Bicycle Tune-Up Step 3 -- Adjust The Front Wheel Bike Hub
    
      Bicycle Tutor: How to Overhaul Wheel Bearings
    
      Sheldon Brown: Shimano Cassettes &ampamp; Freehubs
    
      Sheldon Brown:Traditional Thread-On Freewheels
    
      Sheldon Brown: Freewheel or Cassette?